- DEFAULT CISCO 2950 SWITCH PASSWORD HOW TO
- DEFAULT CISCO 2950 SWITCH PASSWORD SERIAL
- DEFAULT CISCO 2950 SWITCH PASSWORD PASSWORD
In this procedure we will assign fastethernet0/18 as our trunk link. Tenth we also need to create a trunk link that will serve as a link to other device in the network.
DEFAULT CISCO 2950 SWITCH PASSWORD PASSWORD
Setting device VLAN database password to rulesġ0. Ninth add a VTP password of rules to the switch such as. Eight change the vtp domain to the name of your choice.Ĭhanging VTP domain name from NULL to Jeremyĩ. By default a Catalyst switch is a VTP server.Ĩ. Seventh we need to configure our switch as a VTP server or a client if there is another switch. VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2ħ. Sixth to verify our VLAN configurations we need to see it by using the Show VLAN command.ġ default active Fa0/1, Fa0/10, Fa0/11, Fa0/12ġ0 VLAN0010 active Fa0/2, Fa0/3, Fa0/4, Fa0/5ġ6 VLAN0016 active Fa0/6, Fa0/7, Fa0/8, Fa0/9 Switch1(config-if-range)#switchport access vlan 16Ħ. Switch1(config)#interface range fastethernet0/6-9 Fifth assign ports to VLAN 16 starting from ports fastethernet0/6 to fastethernet0/9. Switch1(config-if-range)#switchport access vlan 10ĥ. Switch1(config)#interface range fastethernet0/2-5 Fourth we need to assign ports starting from port fastethernet0/2 to fastethernet0/5 to VLAN 10. Please consult userĭocumentation for configuring VTP/VLAN in config mode.Ĥ. % Warning: It is recommended to configure VLAN from config mode,Īs VLAN database mode is being deprecated.
Third we need to add VLAN 10 and VLAN 16 to the switch. %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to upģ. %LINK-5-CHANGED: Interface Vlan1, changed state to up After giving the switch a host name we proceed with assigning an IP address to the VLAN1 of the switch. %SYS-5-CONFIG_I: Configured from console by consoleĢ. First we need to assign a host name to the switch.Įnter configuration commands, one per line.
DEFAULT CISCO 2950 SWITCH PASSWORD HOW TO
Enter 2 and press Enter to save the configuration to NVRAM and exit, and youhave successfully configured the Cisco 2950 switch.Our topic for today will focus on how to configure the VLAN on a Catalyst 2950 Series Switch.ġ. The switch will now display the current configuration and offer you threechoices.7. Answer no when prompted to enable as a cluster command switch and pressEnter. Accept the default to the Configure IP on this interface question by pressing Enter.Enter the IP address and subnet mask information given to you by your networkadministrator in response to the next two prompts.6. Accept the default to the SNMP Network Management prompt by pressing Enter.Enter vlan1 for the interface used to connect to the management network, andĢ. Be sure to write down the passwordsand store them in a secure place.4. If these werenot issued by your network administrator, you may choose your own passwords.Press Enter after entering each password. Enter the enable secret password, the enablepassword and the virtual terminal password at the respective prompts. Enter a host name of your choosing at the host name prompt, or press Enter toaccept the default of Switch. Press Enter to accept thedefaults for the prompts that ask if you would like to enter the initial configurationdialog and if you would like to enter basic management setup.3. If you have properly configured theterminal session, you will see the Cisco boot messages. Configure the session for 9600 baud, 8 data bits, 1 stop bit, noparity and no flow control. HyperTerminal, Putty or any other terminal emulator will workfine for this step. Power on the computer, and set up a terminal session using your computersterminal software.
The console port end isan RJ-45 jack, which resembles a telephone jack connector, but is a little bit larger.2.
DEFAULT CISCO 2950 SWITCH PASSWORD SERIAL
The cable that comes with the switch istypically blue, and the serial end is a 9-pin d-shell connector. Connect the serial cable that came with the switch to the console port on theswitch and to a serial port on your computer. Before you start, be sure to get the network address and password information you will need from your network administrator.Guide: How to Configure a Catalyst 2950 Cisco Switch1. In addition to the standard console and aux ports, the Cisco 2950 comes with 12, 24 or 48 Ethernet ports, depending on the model. The Cisco Catalyst 2950 switch is a great example of Ciscos dedication to quality and efficiency. HOW TO CONFIGURE A CATALYST 2950 CISCO SWITCH? Cisco has long been a player in the networking industry, and routers and switchesform the core of its product offerings.
0 kommentar(er)
